This crown cutting jig makes cutting and installing crown molding a BREEZE!
If you’ve ever cut crown molding on a miter saw, you know what a pain it can be. I used to have to keep example pieces of molding with the cuts nearby to remind myself every time I do it because it can be so confusing.
To get the perfect cut, there’s a lot of flipping and reversing (anyone else singing “is it worth it, let me work it?”), and making sure the crown lays just right on the saw.
I’ve tried coping the crown molding joints (using a hand saw to “cope” the ends of the crown) and can never get it right.
But THIS, my friends, is the best method of them all!
If you’ve read about my projects for any length of time, you know how much I love decorative trim and molding in a room.
It adds so much!:
I recently finished up the molding in our basement using this helpful jig, and it took half the time it used to:
I’m SO glad to have this done! It only took two years. 🙂
The character that crown molding adds to a room works beautifully for both traditional and modern spaces.
This post may contain affiliate links for your convenience.
I may earn a small commission when you make a purchase through links.
This small room has eight corners though, and cutting crown molding is one of my least favorite DIY jobs. Installing isn’t bad, but the cutting is a pain!
So I finally looked picked up this crown cutting tool I’ve seen a few times online.
I watched the video and kept saying to myself…there’s no way it’s that easy. I was wrong!
First up, they provide these little angle finders that are stored on the jig:
Place your crown on a flat surface (wall or a table) and place the angle piece inside the back of the molding till you get the right fit.
For example, this one is not good:
But this one (38 degree angle) is perfect!:
Crown molding comes in a few “spring angles” so these little angle finders are incredibly helpful!
The spring angle is the angle from the crown when it’s installed to the wall behind it.
This is what keeps it at the perfect angle while cutting the crown molding on the saw.
Their video shares where to place the jig for both inside and outside corner cuts, as well as the direction your saw blade should be going. (There are also images on the actual jig to reference.)
I tried my first piece of molding, held it up in the corner, and started to believe. 😉
I laughed out loud when I held the first two pieces up next to each other and they matched perfectly. I mean…where has this thing been all my life??
I always recommend starting your crown molding at a corner — meeting in the corners is the most important part.
To use this jig on your saw, all you have to do is place your crown in front of the saw fence (decorative side out), then push the jig up to it.
You’ll want to make sure the bottom of the crown is flush against the saw guard at the bottom and the top of the crown is leaning against the jig:
Make sure your jig is out of the way of the saw blade, then cut in the direction for your inside or outside cut.
Most corners will require a 45-degree miter cut, but occasionally I’ve needed a 33 or 23-degree angle.
You can use a protractor to find your corner angle if needed!
The visuals for the angled cuts on the jig are incredibly helpful — it’s a bit confusing to remember at first, but after a few cuts you’ll get it down quick.
You’ll want to mark your measurements on the back of your crown, not the front, because all of your cuts will be made from the back of the molding.
This is nice because you don’t mark up the front of your trim with a pencil line!
My first two pieces with this tool were for an outside corner and they met up PERFECTLY. Look at that tight seam!:
And the inside corner pieces were excellent as well!:
I cannot tell you how much time (and actual crown molding!) this jig has saved me! When using a compound miter saw without this jig, you have to remember how to place the crown, turn it upside down to cut from the bottom of the crown, etc.
Even though I’ve cut crown numerous times, it was usually frustrating and time consuming to get just right.
I’m KICKING myself for not getting one sooner! This knocks off half the time of what I would normally spend installing crown molding.
Total game changer. Now I’m eyeing all the rooms that could use this trim!
Have you ever attempted cutting crown molding? If it’s intimidated you, I highly suggest using a jig like this for your saw!
